User Tools
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
resources:rc4 [2019/07/11 22:04] jgoeders |
resources:rc4 [2019/11/01 16:39] (current) jgoeders |
||
|---|---|---|---|
| Line 6: | Line 6: | ||
| As you may be aware, if we XOR a value with another value twice, we get back the original value (''A ^ B ^ B == A''). Thus, if we use the same key to generate the same pseudo-random stream of bytes, and XOR'd them with the cyphertext, we will get back the original plaintext. Using the same key and algorithm for encryption and decryption makes RC4 a **symmetric** encryption algorithm. This means that the provided module can be used to perform either encryption or decryption. | As you may be aware, if we XOR a value with another value twice, we get back the original value (''A ^ B ^ B == A''). Thus, if we use the same key to generate the same pseudo-random stream of bytes, and XOR'd them with the cyphertext, we will get back the original plaintext. Using the same key and algorithm for encryption and decryption makes RC4 a **symmetric** encryption algorithm. This means that the provided module can be used to perform either encryption or decryption. | ||
| - | Assuming one is using the provided module to perform RC4 decryption, the cyphertext is provided to the ''bytes_in'' input, and the key to the ''key'' input. The decryption process begins when the ''start'' signal is raised, and when completed, the output ''done'' signals will be high for a single cycle. The resulting plaintext is available from the ''bytes_out'' output. | + | Assuming one is using the provided module to perform RC4 decryption, the cyphertext is provided to the ''bytes_in'' input, and the key to the ''key'' input. The decryption process begins when the ''enable'' signal is raised, and when completed, the ''done'' output will be high for a single cycle. The resulting plaintext is available from the ''bytes_out'' output, which won't change until you start a new encryption/decryption process (by lower and raising the enable signal). |
| ^ Module Name = decrypt_rc4 ^^^^ | ^ Module Name = decrypt_rc4 ^^^^ | ||
| Line 14: | Line 14: | ||
| | clk | Input | 1 | 100 MHz Clock | | | clk | Input | 1 | 100 MHz Clock | | ||
| | reset | Input | 1 | Active-high reset | | | reset | Input | 1 | Active-high reset | | ||
| - | | start | Input | 1 | Active-high, start encryption/decryption | | + | | enable| Input | 1 | Set high to start running the decryption. Once started the decryption will continue until finished. You need to lower this signal and then raise it again to start a new decryption process. | |
| | key | Input | 24 | Encryption key | | | key | Input | 24 | Encryption key | | ||
| | done | Output | 1 | Active-high for one cycle when the encryption/decryption completes| | | done | Output | 1 | Active-high for one cycle when the encryption/decryption completes| | ||
| Line 21: | Line 21: | ||
| Click the link below to download the file. | Click the link below to download the file. | ||
| - | <file SystemVerilog decrypt_rc4.sv> | + | <file Verilog decrypt_rc4.sv> |
| module decrypt_rc4 #( | module decrypt_rc4 #( | ||
| parameter BYTES_LEN = 16 | parameter BYTES_LEN = 16 | ||
| Line 27: | Line 27: | ||
| input wire logic clk, // Clock | input wire logic clk, // Clock | ||
| input wire logic reset, // Active-high reset | input wire logic reset, // Active-high reset | ||
| - | input wire logic start, // Start encryption/decryption | + | input wire logic enable, // Start encryption/decryption |
| input wire logic [23:0] key, // 3 byte key | input wire logic [23:0] key, // 3 byte key | ||
| input wire logic [(BYTES_LEN * 8) - 1:0] bytes_in, // byte stream in | input wire logic [(BYTES_LEN * 8) - 1:0] bytes_in, // byte stream in | ||
| Line 101: | Line 101: | ||
| case(cs) | case(cs) | ||
| S_INIT: | S_INIT: | ||
| - | if (start) | + | if (enable) |
| cs <= S_LOOP1; | cs <= S_LOOP1; | ||
| S_LOOP1: | S_LOOP1: | ||
| Line 129: | Line 129: | ||
| S_update_text_out: begin | S_update_text_out: begin | ||
| if (msg_byte_idx == 0) begin | if (msg_byte_idx == 0) begin | ||
| - | cs <= S_INIT; | + | cs <= S_DONE; |
| done <= 1'b1; | done <= 1'b1; | ||
| end else begin | end else begin | ||
| Line 135: | Line 135: | ||
| end | end | ||
| end | end | ||
| + | S_DONE: | ||
| + | if (!enable) | ||
| + | cs <= S_INIT; | ||
| endcase | endcase | ||
| end | end | ||
